I updated some of the forum settings; please try again uploading the files it should work now
a view from the top of the spectrometer is also useful for debugging
Search found 98 matches
- Sat Mar 23, 2024 1:46 pm
- Forum: OpenRAMAN
- Topic: Tuning Spectral Distribution - only able to see a portion of full spectrum
- Replies: 5
- Views: 227
- Fri Mar 22, 2024 8:12 am
- Forum: OpenRAMAN
- Topic: Tuning Spectral Distribution - only able to see a portion of full spectrum
- Replies: 5
- Views: 227
Re: Tuning Spectral Distribution - only able to see a portion of full spectrum
Hi LaurenM, I don't see the attached file. Could you upload it again? One possibility (to be checked) which happens often is that you might be looking at the 2nd order of the grating which doubles the dispersion of the grating (the spectrum therefore spans on twice the range). You can already check ...
- Wed Mar 20, 2024 6:53 am
- Forum: OpenRAMAN
- Topic: Any experience with PCBWay CNC service?
- Replies: 4
- Views: 283
Re: Any experience with PCBWay CNC service?
Yes, resin prints tend to be very brittle. For the cuvette, I recommend SLS technology. Resin is essentially useful when you want very small details like in the laser holder.
- Fri Mar 08, 2024 8:39 am
- Forum: OpenRAMAN
- Topic: Camera Not Detected
- Replies: 5
- Views: 1076
Re: Camera Not Detected
Hi,
That's normal -- you cannot connect twice to the camera
It's a common problem people meet but there is nothing to do, it's just that the camera is not made to support multiple connections.
That's normal -- you cannot connect twice to the camera
It's a common problem people meet but there is nothing to do, it's just that the camera is not made to support multiple connections.
- Sun Mar 03, 2024 8:44 am
- Forum: OpenRAMAN
- Topic: Camera Not Detected
- Replies: 5
- Views: 1076
Re: Camera Not Detected
Can you open spinview and take a screenshot of the camera list ? without doing anything else
- Sat Mar 02, 2024 8:34 am
- Forum: OpenRAMAN
- Topic: Camera Not Detected
- Replies: 5
- Views: 1076
Re: Camera Not Detected
Hi,
Can you double check the followings ?
Can you double check the followings ?
- is the spinview software closed when you try to connect to the camera using SpectrumAnalyzer?
- is the ip address of the camera in the valid range ?
- Fri Feb 23, 2024 2:58 pm
- Forum: OpenRAMAN
- Topic: Any experience with PCBWay CNC service?
- Replies: 4
- Views: 283
Re: Any experience with PCBWay CNC service?
Not on my side; I'm currently working with Xometry even though I also worked for years with different companies in China and Singapore at my former employer. $109 isn't a lot -- I think Xometry would charge twice that. Don't waste your time with imalize (France) by the way, while they do have good q...
- Fri Feb 23, 2024 7:09 am
- Forum: OpenRAMAN
- Topic: Alignment Question
- Replies: 9
- Views: 437
Re: Alignment Question
3.45 µm pixels, monochrome, very low absolute sensitivity threshold and at least 2048 px horizontally if you're using a 50 mm lens. The FLIR camera I'm using has a IMX265 sensor so you can look at substitutes that relies on the same sensor (in monochrome). Apart from the FLIR and Daheng cameras alre...
- Thu Feb 22, 2024 7:44 am
- Forum: OpenRAMAN
- Topic: Alignment Question
- Replies: 9
- Views: 437
Re: Alignment Question
Sorry, my bad -- for some reason when I googled for the GC1380H it proposed a datasheet for another model and I didn't pay attention to the model number :shock: Here is the correct one : https://www.alliedvision.com/en/camera-selector/detail/prosilica-gc/1380h/ The absolute sensitivity threshold is ...
- Wed Feb 21, 2024 9:08 am
- Forum: OpenRAMAN
- Topic: Alignment Question
- Replies: 9
- Views: 437
Re: Alignment Question
I looked up on Internet to gather some data on this camera model and I found this page : https://vitalvisiontechnology.com/allied-vision-manta-g-145b-poe/ It's an old CCD sensor (ICX285) with a not-so-good light sensitivity. The website mentions an absolute detectivity threshold of 11 e- with a quan...